The Juniper router must be configured to protect against known types of Denial of Service (DoS) attacks by employing organization-defined security safeguards.

From Juniper Router NDM Security Technical Implementation Guide

Part of SRG-APP-000435-NDM-000315

Associated with: CCI-002385

JUNI-ND-001210_rule The Juniper router must be configured to protect against known types of Denial of Service (DoS) attacks by employing organization-defined security safeguards.

Vulnerability discussion

DoS is a condition when a resource is not available for legitimate users. When this occurs, the organization either cannot accomplish its mission or must operate at degraded capacity.This requirement addresses the configuration of network devices to mitigate the impact of DoS attacks that have occurred or are ongoing on device availability. For each network device, known and potential DoS attacks must be identified and solutions for each type implemented. A variety of technologies exist to limit or, in some cases, eliminate the effects of DoS attacks (e.g., limiting processes or restricting the number of sessions the device opens at one time). Employing increased capacity and bandwidth, combined with service redundancy, may reduce the susceptibility to some DoS attacks.The security safeguards cannot be defined at the DoD level because they vary according to the capabilities of the individual network devices and the security controls applied on the adjacent networks (for example, firewalls performing packet filtering to block DoS attacks).

Check content

Review the router configuration to verify that it is compliant with this requirement. Step 1: Verify that the loopback interfaces has been configured with an input filter. The example below defined a control plane policing (CoPP) filter named CoPP_Policy. interfaces { … … … lo0 { unit 0 { family inet { filter { input CoPP_Policy; } address 5.5.5.5/32; } } } } Step 2: Verify that the filter will protect against DoS attacks. firewall { … … … } filter CoPP_Policy { term CRITICAL { from { protocol [ ospf pim tcp ]; source-port bgp; destination-port bgp; } then policer CRITICAL; } term IMPORTANT { from { source-address { 10.1.1.0/24; } protocol tcp; destination-port [ ssh snmp ntp ]; } then { policer IMPORTANT; discard; } } term NORMAL { from { protocol icmp; icmp-type [ echo-reply echo-request ]; icmp-code [ ttl-eq-zero-during-transit port-unreachable ]; } then policer NORMAL; } term UNDESIRABLE { from { protocol udp; destination-port 1434; } then policer UNDESIRABLE; } term ALL-OTHER { from { address { 0.0.0.0/0; } } then policer ALL-OTHER; } } } Step 3: verify that policers configured will restrict bandwidth based on traffic types as shown in the example below. firewall { … … … } policer CRITICAL { filter-specific; if-exceeding { bandwidth-limit 4m; burst-size-limit 1500; } then discard; } policer IMPORTANT { filter-specific; if-exceeding { bandwidth-limit 512k; burst-size-limit 16k; } then discard; } policer NORMAL { filter-specific; if-exceeding { bandwidth-limit 64k; burst-size-limit 2k; } then discard; } policer UNDESIRABLE { filter-specific; if-exceeding { bandwidth-limit 32k; burst-size-limit 1500; } then discard; } policer ALL-OTHER { filter-specific; if-exceeding { bandwidth-limit 32k; burst-size-limit 1500; } then discard; } If the router is not configured to protect against known types of DoS attacks by employing organization-defined security safeguards, this is a finding.

Fix text

Configure the router protect against known types of DoS attacks on the route processor. Implementing a CoPP policy as shown in the example below is a best practice method. Step 1: Configure policers for specific traffic types. set firewall policer CRITICAL filter-specific set firewall policer CRITICAL if-exceeding bandwidth-limit 4000000 burst-size-limit 1500 set firewall policer CRITICAL then discard set firewall policer IMPORTANT filter-specific set firewall policer IMPORTANT if-exceeding bandwidth-limit 512000 burst-size-limit 16000 set firewall policer IMPORTANT then discard set firewall policer NORMAL filter-specific set firewall policer NORMAL if-exceeding bandwidth-limit 64000 burst-size-limit 2000 set firewall policer NORMAL then discard set firewall policer UNDESIRABLE filter-specific set firewall policer UNDESIRABLE if-exceeding bandwidth-limit 32000 burst-size-limit 1500 set firewall policer UNDESIRABLE then discard set firewall policer ALL-OTHER filter-specific set firewall policer ALL-OTHER if-exceeding bandwidth-limit 32000 burst-size-limit 1500 set firewall policer ALL-OTHER then discard Step 2: Configure the CoPP filter by applying policers to the appropriate traffic types. set firewall filter CoPP_Policy term CRITICAL from protocol ospf set firewall filter CoPP_Policy term CRITICAL from protocol pim set firewall filter CoPP_Policy term CRITICAL from protocol tcp destination-port bgp set firewall filter CoPP_Policy term CRITICAL from protocol tcp source-port bgp set firewall filter CoPP_Policy term CRITICAL then policer CRITICAL set firewall filter CoPP_Policy term IMPORTANT from source-address 10.1.1.0/24 set firewall filter CoPP_Policy term IMPORTANT from protocol tcp destination-port ssh set firewall filter CoPP_Policy term IMPORTANT from protocol tcp destination-port snmp set firewall filter CoPP_Policy term IMPORTANT from protocol tcp destination-port ntp set firewall filter CoPP_Policy term IMPORTANT then policer IMPORTANT set firewall filter CoPP_Policy term IMPORTANT from protocol tcp destination-port ssh set firewall filter CoPP_Policy term IMPORTANT from protocol tcp destination-port snmp set firewall filter CoPP_Policy term IMPORTANT from protocol tcp destination-port ntp set firewall filter CoPP_Policy term IMPORTANT then discard set firewall filter CoPP_Policy term NORMAL from protocol icmp icmp-code ttl-eq-zero-during-transit set firewall filter CoPP_Policy term NORMAL from protocol icmp icmp-code port-unreachable set firewall filter CoPP_Policy term NORMAL from protocol icmp icmp-type echo-reply set firewall filter CoPP_Policy term NORMAL from protocol icmp icmp-type echo-request set firewall filter CoPP_Policy term NORMAL then policer NORMAL set firewall filter CoPP_Policy term UNDESIRABLE from protocol udp destination-port 1434 set firewall filter CoPP_Policy term UNDESIRABLE then policer UNDESIRABLE set firewall filter CoPP_Policy term ALL-OTHER from address 0.0.0.0/0 set firewall filter CoPP_Policy term ALL-OTHER then policer ALL-OTHER Step 3: Apply the CoPP filter to the loopback interface. set interface lo0 unit 0 family inet filter input CoPP_Policy

Pro Tips

Powered by sagemincer